D-GuardFon
  
D-GuardFon

THE ULTIMATE WALL PROTECTION SYSTEM

The D-GuardFon wall protection system from D.O.G-Sec closes a significant gap in the perimeter intrusion detection system marketplace by providing a solution specifically designed to protect walls which form all, or part of, the perimeter of a secure site. The D-GuardFon system utilises point sensors capable of detecting mechanical vibration transmitted along the wall as an intruder (or escapee) attempts to climb over or break through the wall. These point sensors are deployed along the wall at intervals of typically 3 metres and are interconnected to form an interlaced phased sensor array capable of detecting hostile activity occurring on the structure of the wall

Examples of such hostile activities might include unaided climbing, rope or ladder aided climbing, drilling, chiselling, or digging under the wall. Historically, protection of perimeter walls has relied on technologies such as active / passive infra-red detection, microwave detection, video motion detection, or systems requiring additional structures such as fences to be attached to the wall to achieve detection.

D-GuardFon offers significant advantages over such technologies in that it is virtually covert and causes minimal aesthetic impact, it requires no power distribution along the perimeter wall, it is not limited to straight lines of detection as are infra-red, microwave, and video detection technologies, and it requires no maintenance of sterile areas adjacent to the wall.

Furthermore, as it forms an integral part of the perimeter wall structure, D-GuardFon provides detection of hostile activity before the intruder manages to breach or climb over the wall. As all security professionals are aware, early detection of hostile activity reduces the probability of loss or damage as a result of the activity.
System Architecture & Advantages 

A typical D-GuardFon system comprises a linear phased array of sensors connected to a D-GuardFon signal analyser module. The schematic diagram below depicts the options available applicable to a D-GuardFon system.

Each D-GuardFon signal analyser caters for zone lengths of up to 100 metres. Applied to a typical wall, this corresponds to an array of 32 detection sensors.

The D-GuardFon signal analyser module may be located adjacent to the sensor array deployed on the wall. In such cases, DC power will be required to power the signal analyser and cabling must be provided to route the alarm signals generated by the analyzer back to the operator interface or annunciation system.



Alternatively, the signal analyser may be located up to 2500 metres from the wall, in which case a cable comprising two twisted pairs of conductors is used to interconnect the sensor array on the wall with the remotely located signal analyser. In many cases, the latter configuration is often preferable as the cost of installation of the twisted pair signal cable is generally much cheaper than providing cables suitable for power distribution and alarm signalling, particularly on larger perimeters.

D-GuardFon sensor arrays can be supplied pre-wired or individually packaged to allow on-site wiring where there may be difficulty in deploying a pre-wired array along the perimeter wall.



Sensor Installation:

Each sensor forming part of a phased array can be packaged, either to allow installation within the structure of the wall, or directly mounted on the surface of the wall

Installation within the wall structure requires a hole to be drilled to accommodate each sensor.



Surface mounted sensors are fixed using proprietary wall fixings and remain visible after installation. Similarly, the interconnecting cable between individual sensors in an array may be clipped directly to the face of the wall, or installed within a groove cut into the wall for this purpose.

In the case of brick walls, the usual approach is to rake back a mortar joint to accommodate the interconnecting cable and then re-point the joint to retain the cable. For most applications, the sensor array is installed along the inside (secure) face of the wall close to the top of the wall.

D-GuardFon Signal Analyser:

Signals detected by D-GuardFon sensor arrays are processed by the signal analyser module and classified as either of hostile origin resulting from intruder activity on the wall, or of non-hostile origin resulting from effects such as weather conditions, vehicular traffic adjacent to the wall, and low flying aircraft

Signals classified as being of hostile origin cause the signal analyser to indicate an alarm event, while signals generated as a result of benign activity such as wind, rain, and similar effects are ignored.

The D-GuardFon signal analyser incorporates powerful digital signal processing algorithms to ensure that this classification process is as accurate as possible so that reliable detection of hostile activity is ensured while at the same time, activity classified as benign, or non-hostile, does not result in false alarms.


The signal analyser is available in two configurations as follows:

Standalone Configuration
In this configuration, each analyser is a separate and self contained module. Each analyser is powered by a 12v DC supply and provides relay contact outputs to indicate the occurrence of alarms and facilitate easy connection of these alarms to external annunciation / control equipment.

Networked Configuration
In this configuration, generally applicable to larger perimeters, each analyser is linked by a ruggedised RS485 communications bus which permits the transmission of alarm data from each analyser back to the site control room. All system adjustment and configuration commands are transmitted from the control room to each analyser as required.

Networked analysers are normally used in conjunction with a PC based management system and IP connectivity is provided to enable use of existing network infrastructures where available

Typical Applications
The D-Guard system may be applied to most types of walls including those constructed of brick, stone, concrete, and steel

Ornamental fences comprising decorative steel panels supported on brick or stone pillars are an ideal application of the D-GuardFon system where reliable detection of climbing on both the steel panels and support pillars is required.

As a general guide, walls with a slenderness ratio (Height/Thickness) of 5:1 or greater may be effectively protected by D-GuardFon sensor.
 
 




  

 


2018– D.O.G-sec participates with 2 different intrusion detection systems at M.O.D test site.

2017– D.O.G-sec deployed and handed over to Eilat Port extra 2,500m of D-Guard SeKtor PID

2016 – D.O.G-sec deployed and handed over to its client extra 1,500 meter of Virtual Fences By Bosch HD cameras with Video Analitics protection to a Solar Plant  at Mechola

2016 - D.O.G-Sec has signed with Ledico an agreement for annual maintenance and service for all the Surveillance IP HD Bosch Cameras & Security systems installed in Matityahu.

2016 - D.O.G-Sec has signed with Ledico an agreement for annual maintenance and service for all the Surveillance IP HD Bosch Cameras & Security systems installed in SARONA MARKET TLV

2015 – D.O.G-sec delivers one more perimeter protection to Port of EILAT

securing 1 site with a unique integrated perimeter protection - PIDCCTV + Video Analytics and Access Control (IP HD Bosch Cameras)

2014 - D.O.G-Sec has signed an agreement for annual maintenance and service for all the Cameras, PIDs Access Control and other security systems installed in the sea Port of Eilat


2013  - D.O.G-sec delivers perimeter protection to "SHELL" in Nigeria

 

 

2013 – D.O.G-sec delivers perimeter protection to" PORT OF EILAT "securing 
4 sites with full perimeter protection - electronic fence and surveillance

 


2013 – D.O.G-sec perimeter protection to The Israeli Electric Corporation

D.O.G.Sec is the official supplier of the Israeli National Electric Company for PID - Perimeter Intrusion Detection, sensors based fences and control centers.






D.O.G sec in winning collaboration with Elbit Systems ! official winners of
 the Israeli Ministry Of Defence test trial for sensor based fences ! it's official ! after 12 months of trial including Special Forces penetration attempts into the protected  area


D.O.G-SEC  2012 - securing a critical assets facility of extreme importance in China ! project conducted through leading Chinese firm "262 factory" located in Xian



NEW ! D
-Guard HFO - concealed underground self berried fiber optic cable ! for a complete unrevealed / discreet intruder detecting over vast  stretches of perimeter 



D.O.G-Sec World-Wide

D.O.G-Sec in China

D.O.G-Sec in Nigeria    

D.O.G-Sec in France    
 
D.O.G-Sec in Thailand   

D.O.G-Sec in India    




2010 - D.O.G-SEC Securing Airport in Kathmandu Nepal by HD IP Cameras.


 

Electronic Fence on Wall



Electronic Fence on RailWays



Electronic Fence on RailWays




Harbor Border and Cities
Long Range Camera

  
spacer

 

  |   About us   |   Solutions   |  Products   |   Downloads   |   Projects   |  Contact Us

 





בניית אתרים  Shopsystem